background image

 

12 

 

 

9.THE BEST WAY TO DRIVE OFF

 

y

  Turn on the turn signal light before moving, and make sure no vehicle is coming from behind. Then, 

drive off.   

§

THE CONTROL OF THROTTLE VALVE HANDLE 

§

 

Acceleration : 

To increase speed.    When riding on an inclined road, turn the throttle valve handle slowly 

to allow the engine to output its power. 

Deceleration :

 To decrease speed. 

 

 

 

 

 

 

 

§

PARKING METHOD 

§

 

y

  when approaching the parking lot: 

1. Turn on the turn signal light early, and pay attention to the vehicles in front, from rear, left and right, then 

take the inner lane and approach slowly. 

2. Return the throttle valve handle back to its original position, and apply brakes in advance. (Brake light 

comes on when braking to warn drivers of vehicles behind.) 

y

 

When stop completely: 

3. Press the turn signal switch back to its original position, and turn the ignition switch key to the “OFF” 

position to shut off the engine. 

4. Get off the motorcycle from left side after the engine has been stopped, and select a parking place 

where the motorcycle will not interfere with traffic and the ground is level, then put down motorcycle’s 
main parking stand. 

5. Hold the steering handle with your left hand, and hold down the front end of saddle or hold the parking 

handle on the lower-left side of saddle with your right hand. 

6. Press the main parking stand with your right foot, put down the main parking stand firmly on the ground.   

To remind you:

 Lock the steering handle and remove the key after parking to prevent the motorcycle 

from being stolen. 

 

 

CAUTION:

   

y

  Park your motorcycle at a safe place where it will not interfere with traffic. 

 

Deceleration 

Acceleration

Summary of Contents for JE05W1-6
























Reviews: