Sym JE05W1-6 Owner'S Manual Download Page 19

 

19 

 

§

CHECKING AND CHANGING FUSES 

§

 

Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having the 
same specified amperage rating (10A &7A). Using a fuse of more than 10 or 7 amperes, a brass or iron wire 
to replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit. 

y

  Remove the storage box, and you’ll find the fuse holder near battery. 

y

  Open the fuse box cover, and pull out the fuse.    Check it for damage or broken. 

y

  Fuses must be firmly secured with wire connectors when replacing. Loose connections will result in 

overhead and damage. 

y

  Use only parts having the specified specification to replace electrical components such as light bulbs. 

Using parts not having the specified specifications for replacement may cause the fuse to blow and 
over-discharge the battery. 

y

  Avoid spraying water directly on or around fuse box when washing the motorcycle. 

y

  If the new fuse burn out quickly again, please check the faulty reason before replace it again.

 

Take 

your motorcycle to your dealer for an inspection if a fuse is blown by unknown causes. 

 
 

 

 

 

 

§

CHECKING THE TURN SIGNAL LIGHTS AND HORN 

§

 

y

  Turn the ignition switch key to the “ON” position. 

y

  Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights 

flashes and also check if the warning buzzer sounds. 

y

  Check turn signal light covers if they are dirty, crack, or loosen. 

y

  Press horn button to check if it works. 

 CAUTION:  

y

  Specified specification bulbs should be used for turn signal lights.    Otherwise, the normal 

operation of turn signal lights will be affected. 

y

  Turn on the turn signal light before turning or switching lane to warn driver of vehicles behind. 

y

  Turn off the turn signal light immediately by pressing its button down after using.    Otherwise, the 

flashing of twin signal lights may confuse the drivers of vehicles behind. 

 

§

CHECKING THE FRONT AND REAR LIGHTS 

§

 

y

  Start engine the head lamp is turned on automatically.    Check if head lamp and rear lamp come on. 

y

  Check the brightness and direction of front light by wall to see if it is correct. 

y

  Check the head lamp cover if it is dirty, crack, or loosen. 

§

CHECKING THE BRAKE LIGHT 

§

 

y

  Turn the ignition switch key to the “ON” position, hold the hand-braking levers for front and rear wheels.   

Check if the brake lights come on. 

y

  Check the brake light cover if it is dirty, crack, or loosen. 

 CAUTION:  

y

  Use only specified specification bulbs, do not use bulbs with different specifications to avoid 

damaging electrical system, burning out bulbs, and discharging the battery. 

y

  Do not modify or add other electrical components to prevent over load or short circuit which may 

result in a fire and burn down the motorcycle in serious cases. 

 

 

 

INSTALLATION

 

Press in from above

 

REMOVE

 

 

Wire

 

Fuse connectors

Summary of Contents for JE05W1-6
























Reviews: