manualshive.com logo in svg

Suzuki DF115A, Owner'S Manual

Share
Download
Suzuki DF115A Owner'S Manual Download Page 82

82

FUSE

1. If equipped with Keyless Start System:

Turn the Keyless Start System OFF. 

If not equipped with Keyless Start System:
Turn the ignition key to the “off” position.

2. Remove the motor cover.
3. Remove the fuse box cover and pull off the

fuse.

NOTE:
Use the fuse puller at the back of fuse box
cover, when the fuse is pulled off and installed.

Fuse box cover

15A

MAIN

RELAY

STARTER

RELAY

SPARE

15A

30A

30A

60A

LOAD

60A

MAIN

PLUG

Fuse puller

4. Inspect the fuse and replace with new fuse if

needed.

NOTE:
If a fuse is blown, try to determine the root
cause and correct it.
If the cause is not corrected, the fuse may be
blown again.

 WARNING

If you replace a blown fuse with a fuse
having a different amperage rating or
with a substitute such as aluminum foil or
a wire, extensive electrical system dam-
age and a fire may result.

Always replace a blown fuse with a fuse
of the same type and rating.

Normal fuse

Main fuse (60A)

Blown fuse

Normal fuse

Blown fuse

Summary of Contents for DF115A




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands