manualshive.com logo in svg

Suzuki DF115A, Owner'S Manual

Share
Download
Suzuki DF115A Owner'S Manual Download Page 55

55

STOPPING THE ENGINE

NOTE:
When it is necessary to stop the engine in an
emergency, pull the emergency stop switch lock
plate out of the emergency stop switch by pull-
ing the emergency stop switch cord.

If equipped with Keyless Start System:

To stop the engine:
1. Shift into “NEUTRAL”.

2. After operating at full throttle, cool off the

engine a few minutes by allowing it to idle or
troll at low speed.

3. Push the main switch to stop the engine.

Side mount
type

Top mount
type

4. Turn the Keyless Start System to OFF

(locked) status by one of the following meth-
ods.

• Make sure that the key-fob is within the

communication range of the keyless con-
trol unit.
Turn the main switch to the “ON & OFF”
(“

”) position and then release it. The

main switch automatically returns to the
“PUSH START/STOP” position.
The buzzer sounds once to notify that the
Keyless Start System has been turned to
OFF (locked) state.

NOTE:
If equipped with Dual Engine:
When either one of the engines of Keyless Start
System is turned OFF, another engine will auto-
matically be turned OFF. 

• While the key-fob is within the communi-

cation range of the keyless control unit,
press the lock button 

1

 on the key-fob. 

The buzzer sounds once to notify that the
Keyless Start System has been turned
OFF (locked).

ON & OFF

ON & OFF

PUSH
START

STOP

PUSH
START

STOP

* If equipped with top mount type 
  remote control box: (Main switch panel) 
  “ON & OFF”        “     ” 

Summary of Contents for DF115A




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands