manualshive.com logo in svg

Suzuki DF115A, Owner'S Manual

Share
Download
Suzuki DF115A Owner'S Manual Download Page 27

27

2. Pull out the emergency stop switch lock

plate.

3. Make sure that remote control handle is in

“NEUTRAL”.

Side mount
type

Top mount
type

4. Top mount type

Using the throttle only function of the remote
control box, move the control handle forward
until the caution buzzer sounds one time.

Side mount type

Using the throttle only function of the remote
control box, move the warm-up lever upward
until the caution buzzer sounds one time.

5. Press the “UP” side of the PTT switch for

three seconds and the buzzer will sound
twice briefly indicating the setting has been
canceled.

6. Return the throttle to the fully closed posi-

tion.

SETTING THE TILT UPPER POSITION 
LIMIT

7. Press the “UP” side of the PTT switch so

that the optimum full tilt up position for the
boat can be obtained.

8. If equipped with Keyless Start System: 

Turn the Keyless Start System ON.

If not equipped with Keyless Start System: 
Turn the ignition key to the “ON” position.

9. Pull out the emergency stop switch lock

plate.

10. Make sure that remote control handle is in

“NEUTRAL”.

11.

Top mount type

Using the throttle only function of the
remote control box, move the control handle
forward until the caution buzzer sounds one
time.

Side mount type

Using the throttle only function of the
remote control box, move the warm-up lever
upward until the caution buzzer sounds one
time.

PTT switch

Side mount
type

Top mount
type

UP

PTT switch

UP

Summary of Contents for DF115A




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands