manualshive.com logo in svg

Suzuki DF115A, Owner'S Manual

Share
Download
Suzuki DF115A Owner'S Manual Download Page 38

38

OPERATION OF TILTING 
SYSTEMS

POWER TRIM AND TILT

The “Power Trim and Tilt” is operated by press-
ing the switch. To tilt the motor up, press the
upper part of the switch. To tilt the motor down,
press the lower part of the switch.

Top mount
type

DOWN

UP

Side mount
type

UP

DOWN

UP

DOWN

NOTE:
If equipped with Top Mount remote control box
in case of Dual engine;
Both engines can be operated together on PTT
switch 

1

 at the port control lever grip.

Each engine can be operated by the switches

2

 at the cover separately.

If equipped with Keyless Start System:

If not equipped with Keyless Start System:

 WARNING

The power trim and tilt (PTT) switch on
the side cover can be accidentally acti-
vated when the Keyless Start System is in
OFF state, resulting in injury. 

Keep all persons away from the outboard
motor to help prevent accidental activa-
tion of the PTT system. 

 WARNING

The power trim and tilt (PTT) switch can
be accidentally activated when the igni-
tion key is off, resulting in injury.

Keep all persons away from the outboard
motor to help prevent accidental activa-
tion of the PTT system. 

Summary of Contents for DF115A




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands