manualshive.com logo in svg

Suzuki DF115A, Owner'S Manual

Share
Download
Suzuki DF115A Owner'S Manual Download Page 29

29

CAUTION SYSTEM

The caution systems are designed to alert you
to certain situations which may cause damage
to your outboard motor.

INDICATOR CHECK

If equipped with Keyless Start System:
Each time when the Keyless Start System is
turned to ON state by turning the main switch to
the “ON & OFF” position and then turning it
back to the “PUSH START/STOP” position, four
lamps – the REV LIMIT 

1

, the OIL 

2

, the

TEMP 

3

 and the CHECK ENGINE 

4

 in the

monitor-tachometer will light and the buzzer will
also sound for the first two seconds.

NOTICE

Your outboard motor may become dam-
aged if you rely on the Caution System to
alert you to any malfunction that may
occur or to give you an indication of the
need for maintenance.

To avoid damage to your outboard motor,
regularly inspect and maintain it.

NOTICE

Continuing to operate your outboard
motor with the Caution System activated
can result in severe damage to your out-
board motor.

If the Caution System activates while you
are operating your outboard motor, stop
the motor as soon as possible and cor-
rect the problem or consult your autho-
rized Suzuki marine dealer for
assistance.

For the next three seconds, the monitor-
tachometer will indicate the total motor operat-
ing hours by means of the lamp flashing and
needle indicating.
After this brief check period, the monitor-
tachometer will return to their stand-by mode
and four lamps will continue to light until when
the Keyless Start System is turned to OFF
State or when the engine is started.

NOTE:
If the caution system is activated, only the cor-
responding lamp will light.

NOTE:
For checking the total motor operating hours,
refer to the CHART OF TOTAL OPERATING
HOURS INDICATION on the last page.

NOTICE

If the Caution System is not working
properly, you may not be alerted to a con-
dition that can cause damage to your out-
board motor.

If the buzzer does not sound when the
Keyless Start System has been turned to
ON state by operating the main switch,
the buzzer may be broken or a failure may
exist in the system circuit. Consult your
authorized Suzuki marine dealer.

Summary of Contents for DF115A




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands