background image

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

13

Installing your Hardware

ports.

7.  Use

 cable to connect to open end of the cable splitter and run to the planned location of your booster. 

Note: Be sure to provide enough separation from outdoor antenna (at least 75 ft. is recommended).

Step 4.  Install the Signal Booster

1.  Select a location close to a working AC outlet. Do not expose the signal booster to excessive heat, 

direct sunlight, moisture, and airtight enclosures.

2.  If you’d like to mount the booster to a wall, mark location of screw tabs on the wall in the desired 

location

3.  Use supplied screws or appropriate screws for surface of mounting location and drill 

through screw 

tab holes on booster.

4.  Connect the outside antenna cable to the signal booster connector marked 

OUTSIDE

Hand-tight-

en the connection.

5.  Connect the inside antenna cable to the signal booster connector marked 

INSIDE.

 

Hand-tighten the 

connection.

6. Connect the AC power cord to the signal booster.
7. Connect the plug on the other end of the 110V AC power outlet.
8. Turn the booster’s power switch on.

Summary of Contents for Fusion5S CA























Reviews: