Supero AS2021M-82R+ User Manual Download Page 93

Page: 93 / 104

B-1

Appendix B: BIOS POST Checkpoint Codes

Appendix B

BIOS POST Checkpoint Codes

When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O

port 0080h. If the computer cannot complete the boot process, diagnostic equipment

can be attached to the computer to read I/O port 0080h.

B-1 Uncompressed

Initialization

Codes

The uncompressed initialization checkpoint codes are listed in order of execution:

Checkpoint Code Description

D0h

The NMI is disabled. Power on delay is starting. Next, the initialization code check-
sum will be veriﬁ ed.

D1h

Initializing the DMA controller, performing the keyboard controller BAT test, starting
memory refresh and entering 4 GB ﬂ at mode next.

D3h

Starting memory sizing next.

D4h

Returning to real mode. Executing any OEM patches and setting the Stack next.

D5h

Passing control to the uncompressed code in shadow RAM at E000:0000h. The
initialization code is copied to segment 0 and control will be transferred to segment
0.

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands