Supero AS2021M-82R+ User Manual Download Page 12

Page: 12 / 104

1-2

AS2021M-T2R+/2021M-82R+ User's Manual

1-2 Serverboard

Features

At the heart of the 2021M-T2R+/2021M-82R+ lies the H8DME-2/H8DM8-2, a dual

processor serverboard based on the nVidia MCP55 Pro chipset and designed to

provide maximum performance. Below are the main features of the H8DME-2/

H8DM8-2. (See Figure 1-1 for a block diagram of the MCP55 Pro chipset).

Processors

The H8DME-2/H8DM8-2 supports single or dual AMD Opteron 2000 Series, Socket

F type processors. Please refer to the serverboard description pages on our web

site for a complete listing of supported processors (www.supermicro.com/aplus).

Memory

The H8DME-2/H8DM8-2 has sixteen 240-pin DIMM slots that can support up to

32/32/64 GB of registered ECC DDR2-667/533/400 SDRAM. The memory operates

in an interleaved conﬁ guration and requires requires modules of the same size and

speed to be installed two at a time. See Chapter 5 Section 5 for details.

Serial ATA

A SATA controller is integrated into the chipset to provide a six-port Serial ATA

subsystem, which is RAID 0, 1, 0+1, 5 and JBOD supported. The Serial ATA drives

are hot-swappable units.

Note:

The operating system you use must have RAID support to enable the hot-

swap capability and RAID function of the Serial ATA drives.

SCSI Accessories 2021M-82R+ only)

One (1) dual-channel SCSI backplane (BPN-SCA-825S2)

One (1) Ultra320 SCSI 6-in ribbon cable (CBL-037L-U320)

One (1) Ultra320 SCSI 9-in round cable (CBL-0043L)

Eight (8) SCSI hot-swap drive carriers [MCP-220-00001-03(01)]*

One (1) CD containing drivers and utilities

*The 2021M-T2R+/2021M-82R+ is available in white and black; a "V" following a

part number indicates silver and "B" indicates black.

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands