Supero AS2021M-82R+ User Manual Download Page 88

Page: 88 / 104

7-16

AS2021M-T2R+/2021M-82R+ User's Manual

Startup Delay

Use this setting to Enable or

Disable

the startup delay.

Event Message for PEF Action

Use this setting to Enable or

Disable

event messages for a PEF action.

BMC Watch Dog Timer Action

This setting is used to set the Watch Dog function. The options are

Disabled

Reset System, Power Down and Power Cycle.

7-4 Boot

Menu

This feature allows the user to conﬁ gure the following items:

Boot Device Priority

This feature allows the user to prioritize the boot sequence from the available

devices.

Hard Disk Drives

This feature allows the user to specify the boot sequence from available hard disk

drives.

Removable Drives

This feature allows the user to specify the Boot sequence from available remov-

able drives.

CD/DVD Drives

This feature allows the user to specify the Boot sequence from available CD/DVD

drives.

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands