Supero AS2021M-82R+ User Manual Download Page 66

Page: 66 / 104

6-2

AS2021M-T2R+/2021M-82R+ User's Manual

Figure 6-1. Front and Rear Chassis Views

System Reset

6-2 Control

Panel

The control panel (located on the front of the chassis) must be connected to the

JF1 connector on the serverboard to provide you with system status indications. A

ribbon cable has bundled these wires together to simplify the connection. Connect

the cable from JF1 on the serverboard to JP4 on the Control Panel PCB (printed

circuit board). Make sure the red wire plugs into pin 1 on both JF1 and JP4. Pull

all excess cabling out of the airﬂ ow path. The LEDs inform you of system status.

See Chapter 3 for details on the LEDs and the control panel buttons. Details on

JF1 can be found in Chapter 5.

Control Panel

Main Power

Slim DVD-ROM Drive

3.5" Drive Bays (2)

SATA/SCSI Drives (8)

Floppy Drive (optional)

Ethernet Ports

USB Ports

Keyboard/Mouse Ports

COM1 Port

7 Low-Proﬁ le PCI Slots

VGA Port

USB Ports (2), COM Port

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands