Supero AS2021M-82R+ User Manual Download Page 53

Page: 53 / 104

Chapter 5: Advanced Serverboard Setup

5-19

Power Fail Alarm Reset
Header

Connect JAR to the alarm reset but-

ton on your chassis (if available) or to

a microswitch to allow you to turn off

the alarm that sounds when a power

supply module fails. See the table on

the right for pin deﬁ nitions.

Alarm Reset Header

Pin Deﬁ nitions (JAR)

Pin# Deﬁ nition

Ground

Reset Signal

Compact Flash Power
Header

A Compact Flash Card Power header

is located at JWF1. For the Compact

Flash Card to work properly, you will

ﬁ rst need to connect the device's power

cable to JWF1 and correctly set the

Compact Flash Jumper (JCF1).

Compact Flash

Power Header

Pin Deﬁ nitions (JWF1)

Pin# Deﬁ nition

+5V

Ground

Signal

SGPIO

SGPIO1 and SGPIO2 (Serial General

Purpose Input/Output) provide a bus

between the SATA controller and

the SATA drive backplane to provide

SATA enclosure management func-

tions. Connect the appropriate cables

from the backplane to the SGPIO1

and SGPIO2 header(s) to utilize

SATA management functions on your

system.

SGPIO Header

Pin Deﬁ nitions (SGPIO1, SGPIO2)

Pin# Deﬁ nition Pin # Deﬁ nition

Ground

Data

Load

Ground

Note:

NC indicates no connection.

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands