Supero AS2021M-82R+ User Manual Download Page 11

Page: 11 / 104

Chapter 1

Introduction

1-1 Overview

The AS2021M-T2R+/2021M-82R+ is a high-end server that is comprised of two

main subsystems: the SC825TQ-R700LP/SC825S2-R700LP 2U server chassis and

the H8DME-2/H8DM8-2 dual AMD processor serverboard. Please refer to our web

site for information on operating systems that have been certiﬁ ed for use with the

2021M-T2R+/2021M-82R+ (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included with the 2021M-T2R+/2021M-82R+, as listed below:

Three (3) 8-cm hot-swap chassis fans (FAN-0094L)

One (1) air shroud (MCP-310-00025-00)

Two (2) CPU passive heatsinks (SNK-P0023P)

One (1) DVD-ROM drive (DVM-PNSC-824)

One (1) ﬂ oppy disk drive, optional (FPD-TEAC-SB)

One (1) cable for DVD drive (CBL-0139L)

One (1) ﬂ oppy cable (CBL-040L)

One (1) front control panel cable (CBL-0087)

One (1) rail set (MCP-290-00002-00)

SATA Accessories (2021M-T2R+ only)

One (1) SATA backplane (BPN-SAS-825TQ)

One (1) 2-ft SATA cable (CBL-0044L)

Two (2) 35-cm SATA cables (CBL-0061L)

Two (2) SGPIO ribbon cables (CBL-0157L)

Two (2) 48-cm SATA cables (CBL-0178L)

One (1) 70-cm SATA cable (CBL-0179L)

Eight (8) SATA hot-swap drive carriers [MCP-220-00001-03(01)]*

(The chassis has eight carriers but only six SATA drives are supported.)

Chapter 1: Introduction

1-1

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands