Supero AS2021M-82R+ User Manual Download Page 101

Page: 101 / 104

C-1

Appendix C: System Speciﬁ cations

Appendix C

System Speciﬁ cations

Processors

Single or dual AMD Opteron 2000 series (Socket F) type processors

Note: Please refer to our web site for a complete listing of supported processors.

Chipset

nVidia MCP55 Pro and NEC 720400 chipset

BIOS

8 Mb AMI

Flash ROM

Memory Capacity

Sixteen 240-pin DIMM sockets supporting up to 32/32/64 GB of registered

ECC

DDR2-667/533/400

SDRAM.

Note: Memory may be installed to provide interleaved or non-interleaved conﬁ gurations. See

the memory section in Chapter 5 for details.

Serial ATA Controller (2021M-T2R+ only)

On-chip controller for six-port Serial ATA (RAID 0, 1, 0+1, 5 and JBOD

supported)

SCSI Controller (2021M-82R+ only)

On-chip controller for eight-por t Serial ATA (R AID 0, 1, 10 and JBOD

supported)

SCSI/SATA Drive Bays

Eight (8) hot-swap drive bays to house eight (8) standard SCSI or six (6)

standard SATA drives

Peripheral

Drive

Bays

One (1) slim ﬂ oppy drive

One (1) slim DVD-ROM drive

Summary of Contents for AS2021M-82R+









































































































Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands

Supero AS2021M-82R+, User Manual

Search results

Summary of Contents for AS2021M-82R+

Reviews:

Brands by name

Popular brands