Supero AS-1011M-Ni User Manual Download Page 70

Page: 70 / 100

7-2

AS1011M-Ni User's Manual

7-2 Main

Menu

When you fi rst enter AMI BIOS Setup Utility, you will see the Main Menu screen.

You can always return to the Main Menu by selecting the

Main

tab on the top of

the screen with the arrow keys.

The Main Menu screen provides you with a system overview, which includes the

version, built date and ID of the AMIBIOS, the type, speed and number of the

processors in the system and the amount of memory installed in the system.

System Time/System Date

You can edit this fi eld to change the system time and date. Highlight

System Time

System Date

using the <Arrow> keys. Enter new values through the keyboard.

Press the <Tab> key or the <Arrow> keys to move between fi elds. The date must

be entered in DAY/MM/DD/YYYY format. The time is entered in HH:MM:SS format.

Please note that time is in a 24-hour format. For example, 5:30 A.M. appears as

05:30:00 and 5:30 P.M. as 17:30:00.

7-3 Advanced Settings Menu

Boot Features

Quick Boot

If Enabled, this option will skip certain tests during POST to reduce the time

needed for the system to boot up. The options are

Enabled

and Disabled.

Quiet Boot

Disabled

, normal POST messages will be displayed on boot-up. If Enabled,

this display the OEM logo instead of POST messages.

Add-On ROM Display Mode

Set this option to display add-on ROM (read-only memory) messages. Select

Force BIOS

to allow the computer system to force a third party BIOS to display

during system boot. Select Keep Current to have the computer system display

the BIOS information during system boot.

Boot up Num-Lock

Set this value to allow the Number Lock setting to be modifi ed during boot up.

The options are

and Off.

Summary of Contents for AS-1011M-Ni





































































































Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands

Supero AS-1011M-Ni, User Manual

Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands