Supero AS-1011M-Ni User Manual Download Page 49

Page: 49 / 100

Chapter 5: Advanced Motherboard Setup

5-15

Fan Headers

The H8SMU has fi ve fan headers,

which are designated FAN1 through

FAN5. See the table on the right for

pin defi nitions.

Note:

when using active heatsinks

(those with fans), connect the heatsink

fan for the CPU to the FAN1 header.

Serial Ports

The COM1 serial port is located be-

side the VGA port. COM2 is a header

located near the floppy connector.

Refer to the table on the right for pin

defi nitions.

LAN1/2 (Ethernet Ports)

Two Gigabit Ethernet ports (desig-

nated LAN1 and LAN2) are located

beside the VGA port. These Ethernet

ports accept RJ45 type cables.

Note:

NC indicates no connection.

Serial Port Pin Defi nitions

(COM1/COM2)

Pin # Defi nition

DCD

DSR

RXD

RTS

TXD

CTS

DTR

Ground

Fan Header

Pin Defi nitions

(FAN1-5)

Pin# Defi nition

Ground (Black)

+12V (Red)

Tachometer

USB Headers

Two additional USB2.0 headers

(USB2/3) are included on the moth-

erboard. These may be connected

to provide front side access. A USB

cable (not included) is needed for the

connection. See the table on the right

for pin defi nitions.

Universal Serial Bus Headers

Pin Defi nitions (USB2/3)

USB2
Pin # Defi nition

USB3
Pin # Defi nition

+5V

PO-

PO+

Ground

Key

No connection

Summary of Contents for AS-1011M-Ni





































































































Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands

Supero AS-1011M-Ni, User Manual

Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands