Supero AS-1011M-Ni User Manual Download Page 56

Page: 56 / 100

5-22

AS1011M-Ni User's Manual

5-11 Onboard Indicators

LAN1/LAN2 LEDs

The Ethernet ports (located beside

the VGA port) have two LEDs. On

each Gb LAN port, one LED indicates

activity when blinking while the other

LED may be amber or off to indicate

the speed of the connection. See

the table on the right for the func-

tions associated with the connection

speed LED.

LAN LED

(Connection Speed Indicator)

LED Color Defi nition

Off

10/100 MHz

Amber

1 GHz

Onboard Power LED (DP1)

DP1 is an Onboard Power LED. When

this LED is lit, it means power is pres-

ent on the serverboard. In suspend

mode this LED will blink on and off. Be

sure to turn off the system and unplug

the power cord(s) before removing or

installing components.

UID LED (LE1)

The LE1 LED will illuminate when the

UID button is pressed. Pressing the

button a second time will turn this

LED off. The UID LED is used to

help locate specifi c servers in heavily

populated server racks.

Summary of Contents for AS-1011M-Ni





































































































Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands

Supero AS-1011M-Ni, User Manual

Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands