Supero AS-1011M-Ni User Manual Download Page 23

Page: 23 / 100

Chapter 2: Server Installation

2-7

Figure 2-4. Installing the Server into a Telco Rack

Installing the Server into a Telco Rack

To install the 1011M-Ni into a Telco type rack, use two L-shaped brackets on ei-

ther side of the chassis (four total). First, determine how far follow the server will

extend out the front of the rack. Larger chassis should be positioned to balance

the weight between front and back. If a bezel is included on your server, remove

it. Then attach the two front brackets to each side of the chassis, then the two

rear brackets positioned with just enough space to accommodate the width of the

telco rack. Finish by sliding the chassis into the rack and tightening the brackets

to the rack.

Summary of Contents for AS-1011M-Ni





































































































Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands

Supero AS-1011M-Ni, User Manual

Search results

Summary of Contents for AS-1011M-Ni

Reviews:

Related manuals for AS-1011M-Ni

Brands by name

Popular brands