manualshive.com logo in svg

Supermicro SUPERSERVER 5028TK-HTR, User Manual

Share
Download
Supermicro SUPERSERVER 5028TK-HTR User Manual Download Page 136

B-2

SUPERSERVER 5028TK-HTR/HTTR User's Manual

Note:

  

Do not interrupt

 the BIOS flashing until it has completed.

Note: 

If you cannot locate the "Super.ROM" file in your driver disk, visit our website 

at www.supermicro.com to download the BIOS image to a USB flash device and 

rename it "Super ROM".

2.  Insert the USB device that contains the new BIOS image ("Super.ROM") into 

your USB drive and power on the system 

3.  While powering on the system, keep pressing <Ctrl> and <Home> simultane-

ously on your keyboard until your hear two short beeps. This may take from a 
few seconds to one minute.

4.  After locating the new BIOS binary image, the system will enter the BIOS 

recovery menu as shown below. 

Note

: At this point, you may decide if you want to start with BIOS Recovery. If you 

decide to proceed with BIOS Recovery, follow the procedures below. 

5.  When the screen shown above displays, use the arrow keys to select the item 

"Proceed with flash update" and press the <Enter> key. You will see the BIOS 

recovery progress as shown in the screen below.

Summary of Contents for SUPERSERVER 5028TK-HTR











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands