Supermicro SUPERSERVER 5028TK-HTR User Manual Download Page 120

Page: 120 / 138

7-36

SUPERSERVER 5028TK-HTR/HTTR User's Manual

7-4 Event Logs

Use this feature to configure Event Log settings.



Change SMBIOS Event Log Settings

This feature allows the user to configure SMBIOS Event settings.

Enabling/Disabling Options

SMBIOS Event Log

Select Enabled to enable SMBIOS (System Management BIOS) Event Logging
during system boot. The options are

Enabled

and Disabled.

Runtime Error Logging Support

Select Enable to support Runtime Error Logging. The options are

Enable

and

Disable.

Erasing Settings

Erase Event Log

Select Yes to erase all error events in the SMBIOS (System Management BIOS)
log before an event logging is initialized at bootup. The options are

and Yes.

Summary of Contents for SUPERSERVER 5028TK-HTR











































































































































Search results

Summary of Contents for SUPERSERVER 5028TK-HTR

Reviews:

Related manuals for SUPERSERVER 5028TK-HTR

Brands by name

Popular brands

Supermicro SUPERSERVER 5028TK-HTR, User Manual

Search results

Summary of Contents for SUPERSERVER 5028TK-HTR

Reviews:

Related manuals for SUPERSERVER 5028TK-HTR

Brands by name

Popular brands