Supermicro AS-1041M-82 User Manual Download Page 69

Page: 69 / 104

Chapter 6: Advanced Chassis Setup

6-7

2. Installing/removing hot-swap SATA/SCSI drives

The SATA/SCSI drive carriers are all easily accessible at the front of the chassis.

These hard drives are hot-pluggable, meaning they can be removed and installed

without powering down the system. To remove a carrier, push the release button

located beside the drive LEDs. Then swing the colored handle fully out and use it

to pull the unit straight out (see Figure 6-5).

Note:

Your operating system must have RAID support to enable the hot-plug ca-

pability of the SATA/SCSI drives.

Figure 6-5. Removing a SATA/SCSI Drive from the Server

SCSI/SATA Backplane

The SCSI/SATA drives plug into a backplane that provides power, drive ID and bus

termination. A RAID controller can be used with the backplane to provide data

security. The operating system you use must have RAID support to enable the

hot-swap capability of the drives. The backplane is already preconﬁ gured, so there

are no jumpers or switches present on it.

Summary of Contents for AS-1041M-82









































































































Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands

Supermicro AS-1041M-82, User Manual

Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands