Supermicro AS-1041M-82 User Manual Download Page 8

Page: 8 / 104

viii

Overheat LED ........................................................................................ 5-16

Wake-On-LAN ........................................................................................ 5-17

Wake-On-Ring ........................................................................................ 5-17

SMB Power Header ............................................................................... 5-17

3rd Power Supply Alarm Reset Header ................................................. 5-17

JLAN 1/2 (Ethernet Ports) ...................................................................... 5-18

Compact Flash Power Headers ............................................................. 5-18

3rd Power Supply Fail Detect Header ................................................... 5-18

SGPIO .................................................................................................... 5-18

5-9 Jumper

Settings

............................................................................................ 5-19

Explanation of Jumpers ......................................................................... 5-19

CMOS Clear ........................................................................................... 5-19

VGA Enable/Disable ............................................................................... 5-20

JLAN Enable/Disable ............................................................................. 5-20

SCSI Controller Enable/Disable ............................................................. 5-20

SCSI Termination Enable/Disable .......................................................... 5-20

Compact Flash Master/Slave ................................................................. 5-21

Watch Dog Enable/Disable .................................................................... 5-20

5-10 Onboard Indicators

....................................................................................... 5-21

JLAN1/JLAN2 LEDs ............................................................................... 5-21

Onboard Power LED .............................................................................. 5-22

5-11 Floppy, IDE, SCSI and SATA Drive Connections ......................................... 5-23

Floppy Connector ................................................................................... 5-23

IDE Connector ........................................................................................ 5-24

SATA Ports ............................................................................................. 5-24

SCSI Connectors ................................................................................... 5-25

5-12 Enabling SATA RAID .................................................................................... 5-26

5-13 Installing Software Drivers ............................................................................ 5-28

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 System

Fans

................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

Replacing System Fans ........................................................................... 6-3

6-4 Drive Bay Installation/Removal ...................................................................... 6-4

6-5 Power Supply ................................................................................................. 6-9

Power Supply Failure ............................................................................... 6-9

Removing/Replacing the Power Supply ................................................... 6-9

AS1041M-T2/1041M-82 User's Manual

Summary of Contents for AS-1041M-82









































































































Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands

Supermicro AS-1041M-82, User Manual

Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands