Supermicro AS-1041M-82 User Manual Download Page 56

Page: 56 / 104

5-22

AS1041M-T2/1041M-82 User's Manual

5-10 Onboard Indicators

JLAN1/JLAN2 LEDs

The Ethernet ports (located beside the

VGA port) have two LEDs. On each

Gb LAN port, the right LED indicates

activity while the left LED may be

green, amber or off to indicate the

speed of the connection. See the

table on the right for the functions as-

sociated with the left LED.

JLAN Left LED

(Connection Speed Indicator)

LED Color Deﬁ nition

Off

10 MHz

Green

100 MHz

Amber

1 GHz

Onboard Power LED (DP2)

DP2 is an Onboard Power LED. When

this LED is lit, it means power is pres-

ent on the serverboard. In suspend

mode this LED will blink on and off. Be

sure to turn off the system and unplug

the power cord(s) before removing or

installing components.

Summary of Contents for AS-1041M-82









































































































Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands

Supermicro AS-1041M-82, User Manual

Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands