Supermicro AS-1041M-82 User Manual Download Page 29

Page: 29 / 104

Chapter 3: System Interface

3-3

Power:

Indicates power is being supplied to the system's power supply

units. This LED should normally be illuminated when the system is operating.

3-4 Drive

Carrier

LEDs

SATA Drives (1041M-T2)

Green:

Each Serial ATA drive carrier has a green LED. When illuminated,

this green LED (on the front of the SATA drive carrier) indicates drive activity. A

connection to the SATA backplane enables this LED to blink on and off when that

particular drive is being accessed. Please refer to Chapter 6 for instructions on

replacing failed SATA drives.

Red:

The red LED to indicate an SATA drive failure. If one of the SATA drives

fail, you should be notiﬁ ed by your system management software. Please refer to

Chapter 6 for instructions on replacing failed SATA drives.

SCSI Drives (1041M-82)

Each SCSI drive carrier has two LEDs.

Green:

When illuminated, the green LED on the front of the SCSI drive car-

rier indicates drive activity. A connection to the SCSI SCA backplane enables this

LED to blink on and off when that particular drive is being accessed.

Red:

The SAF-TE compliant backplane activates the red LED to indicate a

drive failure. If one of the SCSI drives fail, you should be notiﬁ ed by your system

management software. Please refer to Chapter 6 for instructions on replacing failed

SCSI drives.

Summary of Contents for AS-1041M-82









































































































Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands

Supermicro AS-1041M-82, User Manual

Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands