Supermicro AS-1041M-82 User Manual Download Page 88

Page: 88 / 104

7-16

AS1041M-T2/1041M-82 User's Manual

7-4 Boot

Menu

This feature allows the user to conﬁ gure the following items:

Boot Device Priority

This feature allows the user to prioritize the boot sequence from the available de-

vices. The devices to set are:

· 1st Boot Device

· 2nd Boot Device

· 3rd Boot Device

· 4th Boot Device

· 5th Boot Device

Hard Disk Drives

This feature allows the user to specify the boot sequence from available hard disk

drives.

1st Drive

Speciﬁ es the boot sequence for the 1st Hard Drive.

Removable Drives

This feature allows the user to specify the Boot sequence from available remov-

able drives.

1st Drive

Speciﬁ es the boot sequence for the 1st Removable Drive. The options are

1st

Floppy Drive

and Disabled.

CD/DVD Drives

This feature allows the user to specify the Boot sequence from available CD/DVD

drives.

Summary of Contents for AS-1041M-82









































































































Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands

Supermicro AS-1041M-82, User Manual

Search results

Summary of Contents for AS-1041M-82

Reviews:

Related manuals for AS-1041M-82

Brands by name

Popular brands