Superior Fireplaces DRC3500 Installation & Operation Instructions Download Page 12

Page: 12 / 70

Installation

900298-00, 10/2014

Innovative Hearth Products
Superior

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

MANUFACTURED HOME REQUIREMENTS

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes.

Cet appareil peut être installé dans une maison préfabriquée (mobile) déjà installée à demeure si les règlements

locaux le permettent.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for

use with other gases, unless a certified kit is used.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil ne

peut être converti à d’autres gaz, sauf si une trousse de conversion est utilisée.

CAUTION

Ensure that the cross members are not cut or weakened during installation. The structural

integrity of the manufactured home floor, wall, and ceiling / roof must be maintained.

CAUTION

This appliance must be grounded to the chassis of the manufactured home in accordance

with local codes or in the absence of local codes, with the National Electrical Code ANSI /

NFPA 70—latest edition or the Canadian Electrical Code CSA C22.1—latest edition.

LOCATION

In selecting the location, the aesthetic and functional use of the fireplace are primary concerns. However, vent

system routing to the exterior and access to the fuel supply are also important.

Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies.

En raison des températures élevées, l’appareil devrait être installé dans un endroit où il y a peu de

circulation et loin du mobilier et des tentures.

The location should also be free of electrical, plumbing or other heating/air conditioning ducting.
These direct-vent fireplaces are uniquely suited for installations requiring a utility shelf positioned directly above the

fireplace. Utility shelves like these are commonly used for locating television sets and decorative plants.

Be aware that this is a heat producing fireplace. Objects placed above the unit are exposed to elevated temperatures.

Do not insulate the space between the fireplace and the area above it.

The minimum height from the base of the fireplace to the underside of combustible materials used to construct a

utility shelf in this fashion is shown in

Table 9

and

Table 10

Figure 2: Typical Locations and Venting

Vertical Vent

(Rear Vent)

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

Horizontal Vent

(Top Vent)

Vertical Vent

(Top Vent)

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

Horizontal Vent

(Rear Vent with chase)

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

Horizontal Vent

(Rear Vent without chase)

Top Vent

Top V

ent

Top V

ent

Top V

ent

Top V

ent

Rear V

ent

Rear V

ent

Recessed

Installation

Summary of Contents for DRC3500







































































Search results

Summary of Contents for DRC3500

Reviews:

Related manuals for DRC3500

Brands by name

Popular brands

Superior Fireplaces DRC3500, Installation & Operation Instructions

Search results

Summary of Contents for DRC3500

Reviews:

Related manuals for DRC3500

Brands by name

Popular brands