Superior Fireplaces DRC3500 Installation & Operation Instructions Download Page 7

Page: 7 / 70

General Information

900298-00, 10/2014

Innovative Hearth Products
Superior

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

WARNING

Clothing or other flammable material should not be placed on or near the appliance.

AVERTISSEMENT

On ne devrait pas placer de vêtements ni d’autres matières inflammables sur l’appareil ni à proximité.

WARNING

Improper installation or use of this appliance can cause serious injury or death from fire, burns,

explosion or carbon monoxide poisoning.

CAUTION

Hot while in operation. Do not touch. Severe Burns may result. Keep children, clothing

furniture, gasoline and other liquids having flammable vapors away.

ATTENTION

L’appareil est chaud lorsqu’il fonctionne. Ne pas toucher l’appareil. Risque de brûlures

graves. Surveiller les enfants. Garder les vêtements, les meubles, l’essence ou autres

liquides produisant des vapeur inflammables loin de l’appareil.

NOTE:

•

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

•

For use with barrier(s) Part No(s). F1839 (35” Models), F1840 (40” Models), and F1903 (45” Models).

Follow installation instructions.

•

These fireplaces are designed as supplemental heaters, and are not to be used as the primary heat source when

installed in a dwelling.

•

Provide adequate clearances around air openings and adequate accessibility clearance for service and proper

operation. Never obstruct the front or back openings of the fireplace.

•

These fireplaces are designed to operate on natural or propane gas only. The use of other fuels or combination of

fuels will degrade the performance of this system and may be dangerous.

•

These fireplaces must not be connected to a chimney or flue serving a separate solid fuel burning fireplace.

•

Only trim kit(s) supplied by the manufacturer shall be used in the installation of this fireplace.

Remarqué :

•

Seules les trousses de garniture fournies par le fabricant doivent être utilisées pour l’installation de cet appareil.

Summary of Contents for DRC3500







































































Search results

Summary of Contents for DRC3500

Reviews:

Related manuals for DRC3500

Brands by name

Popular brands

Superior Fireplaces DRC3500, Installation & Operation Instructions

Search results

Summary of Contents for DRC3500

Reviews:

Related manuals for DRC3500

Brands by name

Popular brands