Superior Fireplaces DRC3500 Installation & Operation Instructions Download Page 4

Page: 4 / 70

General Information

900298-00, 10/2014

Innovative Hearth Products
Superior

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

THANK YOU FOR YOUR PURCHASE. WE APPRECIATE YOUR BUSINESS!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety

information. Following these safety, care, and operation instructions will help ensure many years of dependable and

enjoyable service from your fireplace.

Please read and understand these instructions before installing,

operating, or servicing this product.

We recommend that our

gas hearth products be

installed and serviced by

professionals who are

certified in the U.S. by the

National Fireplace Institute®

(NFI) as NFI Gas Specialists.

General Information

Important Safety Information ............................................................

Fireplace Installation, Operation, and Maintenance Notices ...............

Packaging ..........................................................................................

Introduction .......................................................................................

Installation

Requirements for the Commonwealth of Massachusetts ................

Cold Climate Insulation ....................................................................

Manufactured Home Requirements .................................................

Location ...........................................................................................

Vent Termination Clearances ...........................................................

Minimum Clearances to Combustibles ............................................

Wall Finishes / Surrounds / Mantels ................................................

Installation Preparation ....................................................................

Installation Sequence ......................................................................

Construct the Fireplace Framing ......................................................

Route the Gas Supply Line to the Fireplace .....................................

Install the Vent System ....................................................................

Complete the Field Wiring ................................................................

Connect the Gas Line .......................................................................

Verify Proper Fireplace Operation ....................................................

Optional: Install the Firebox Liners ..................................................

Traditional: Install the Logs, Volcanic Stone, and Glowing Embers .

Contemporary: Install Floor Panel and Glass Media ........................

Install the Glass Door ......................................................................

Adjust the Air Shutter to Ensure Proper Flame Appearance .............

Install the Hood ...............................................................................

Reinstall Barrier ...............................................................................

Install the Finishing Materials ..........................................................

Attach the Safety-in-Operation Warnings.........................................

Installation Accessories ...................................................................

Gas Conversion Kits ........................................................................

Operation

Maintenance ....................................................................................

Accessory Components ...................................................................

Lighting Instructions .......................................................................

Troubleshooting ...............................................................................

Replacement Parts ..........................................................................

Warranty ..........................................................................................

Summary of Contents for DRC3500







































































Search results

Summary of Contents for DRC3500

Reviews:

Related manuals for DRC3500

Brands by name

Popular brands

Superior Fireplaces DRC3500, Installation & Operation Instructions

Search results

Summary of Contents for DRC3500

Reviews:

Related manuals for DRC3500

Brands by name

Popular brands