background image

6

TA44T  Temperature alarm base unit with wireless transmitter.
R10 

Remote alarm wireless receiver.

SPECIFICATIONS

Power  

12 V  Adapter 120 VAC with 6 ft. cable included 

Probe  

Precision Thermistor with 6 ft. cable (20540)

Alarm Adjustment Range   

-40°F to 160°F (-40° to 71°C) 

Temperature Accuracy 

+/- 2°F (+/- 1°C)

Temperature Units 

 °F or °C, User Selectable

Remote Connections  

Screw type,120VAC, 5 Amps.

Unit Operating Temperature Range 

-10°F to +130°F (-23°C to +54°C)

Mounting  

Flat Surface, external holes provided

Dimensions   

4.9” x 3.1” x 1.5” (12.4cm x 7.9cm x 3.8cm)

Case  

Hi Impact Thermoplastic

NOTE:

This equipment has been tested and found to comply with the limits for a class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is    
 connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes or modifications not expressly approved by the party 
responsible for compliance could void the user’s authority to operate this equipment.

TA44 WARRANTY

LIMITED TO ONE YEAR FROM DATE OF PURCHASE

Sealed Unit Parts Co., Inc. warrants its products to be free from defects in materials and 
workmanship under normal use and service. Sealed Unit Parts Co., Inc. will repair or replace 
without charge any such products it finds to be so defective on its return to Sealed Unit Parts 
Co., Inc. The foregoing is in lieu of all other expressed or implied warranties, including those of 
merchantability or fitness for a particular purpose. The foregoing is also the purchaser’s sole 
remedy and is in lieu of all other guarantees, obligations or liabilities or any consequential or 
incidental damages attributable to negligence or strict liability.

TA44 Manual.indd   7

5/8/2012   4:39:17 PM

Distributed by MicroDAQ.com, Ltd.                   www.MicroDAQ.com                   (603) 746-5524

Summary of Contents for TA44









Reviews: