manualshive.com logo in svg

Sunrise Medical QR-ED, Owner'S Manual, Page: 41 / 51

Share
Download
Sunrise Medical QR-ED Owner'S Manual Download Page 41

101519 Rev. A

41

Q R- E D

X I I .   P R I M A RY   P R O G R A M M I N G   M E N U

XII. PRIMARY PROGRAMMING MENU

(Accessible to user levels 4-5)

A. MOTOR CONTROLLER

The Primary Programming Menu provides access to many basic chair functions, such as
volume levels, actuator speed & acceleration, and Quickie Enhanced Display fine tuning.
The motor controller programming sub-menu provides programming access to the follow-
ing functions:

Definitions

Horn Volume: Sets the volume of the horn as a %
of maximum volume.

Command and Beep: Enables an audio backup
“beep” for all commands.

Beep Volume: Sets the volume of the command
beep.

Backup Alarm: Enables an audio “beep” when the
chair is in reverse.

Keyless Lock: Allows the user to “lock” the power
chair when not in use by holding the mode button
and pushing the joystick forward for more than 5 
seconds. This prevents the chair from being turned
on until it is unlocked with the same command.

Speed: Sets the percent of maximum actuator speed.

Acceleration: Sets the percent of maximum actuator
acceleration.

Quickie Motor Controller

Summary of Contents for QR-ED




















































Reviews:

No comments