Sunrise Medical QR-ED Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 51

Sunrise Medical QR-ED Owner'S Manual Download Page 31

101519 Rev. A

31

Q R- E D

I X .

E. DRIVE PROFILES

The Drive Profiles sub-menu provides a user the option of switching from the current
drive profile to a new drive profile. Each drive profile contains operational settings, such as
max speed, min speed, turning speed, acceleration values, etc. The Drive profile also spec-
ifies the input device used to drive the chair. A user often switches drive profiles when
transitioning from one type of input device to another. From the factory, each drive profile
is set with progressively faster settings: Drive Profile 1, slowest; Drive Profile 4, fastest.

Drive Profiles can be re-programmed by a qualified supplier or technician.

Drive Profiles

Drive Profile 4

Drive Profile 1

Drive Profile 3
Drive Profile 2

Drive 1

Bat

00000 mi

0.0 mi

Drive 2

Bat

00000 mi

0.0 mi

Drive 3

Bat

00000 mi

0.0 mi

Drive 4

Bat

00000 mi

0.0 mi

*Drive Profile

4-choice

operation

menu

«
...
29
30
31
32
33
...
»

Summary of Contents for QR-ED




















































Reviews:

No comments