Sunell Security SN-TPT4231 User Manual Download Page 20

Page: 20 / 87

Quick Configuration

Dual Vision Light Load Thermal PTZ

User Manual

Issue V1.0 (2019-04-03)

Quick Configuration

4.1 Thermal Web

4.1.1 Login and Logout

You must use Internet Explorer 8 or a later version to access the web management
system; otherwise, some functions may be unavailable.

Step 1

Open the Internet Explorer, enter the IP address of IP camera (default value:

192.168.0.121) in the address box, and press Enter.

The login page is displayed, as shown in Figure 4-1.

Figure 4-1

Step 2

Input the User name and password.



The default user name is

admin.

The default password is

admin

. Change the password

when you login the system for first time to ensure system security.



You can change the system display language on the login page.

Step 3

Click Login.

The main page is displayed.

----End

Summary of Contents for SN-TPT4231
























































































Search results

Summary of Contents for SN-TPT4231

Reviews:

Related manuals for SN-TPT4231

Brands by name

Popular brands

Sunell Security SN-TPT4231, User Manual

Search results

Summary of Contents for SN-TPT4231

Reviews:

Related manuals for SN-TPT4231

Brands by name

Popular brands