Sunell Security SN-TPT4231 User Manual Download Page 58

Page: 58 / 87

Visible-light Parameter Configuration

Dual Vision Light Load Thermal PTZ

User Manual

Issue V1.0 (2019-04-03)

Figure 6-4

Scene mode interface

Table 6-2describes the FFC mode parameters.

Table 6-2

FFC mode parameters description

Parameter

Description

Configuration
Method

Scene

It indicates the working mode of a
camera..



Outdoor: It applies to outdoor
scenarios.



Indoor: It applies to indoor
scenarios.

[Configuration method]

Select from the drop-
down list

[Default value]

Outdoor

Mirror

It is used to select the pixel location of
an image.



Normal: The image does not flip.



Horizontal: The image flips to the
left and right.



Vertical: The image flips up and
down.



Horizontal and vertical: The image
rotates at 180 degrees.

[Setting method]

Select a value from the
drop-down list.

[Default value]

Normal

Summary of Contents for SN-TPT4231
























































































Search results

Summary of Contents for SN-TPT4231

Reviews:

Related manuals for SN-TPT4231

Brands by name

Popular brands

Sunell Security SN-TPT4231, User Manual

Search results

Summary of Contents for SN-TPT4231

Reviews:

Related manuals for SN-TPT4231

Brands by name

Popular brands