Sunell Security SN-TPT4231 User Manual Download Page 65

Page: 65 / 87

Dual Vision Light Load Thermal PTZ
User Manual

Visible-light Parameter Configuration

Issue V1.0 (2019-04-03)

Figure 6-8

Noise Reduction interface

Table 6-6 describes DNR parameters.

Table 6-6

DNR parameters description

Parameter

Meaning

Configuration Method

3D NR

Reduce noise of image.

[Configuration method]

Select from the drop-
down list

[Default value]

Auto

Max Strength

It is valid in auto noise filter mode.
When the parameter value is

, the

noise filter is disabled. When the
parameter value is greater than

, the

noise filter is enabled, and the system
automatically adjusts the noise filter
level based on the ambient brightness
without exceeding the value of this
parameter.

[Setting method]

Drag the slider.

[Default value]

6.2.8 Enhance Image

Figure 6-9 shows the enhance image interface and Table 6-7 shows the enhance image
parameter.

Summary of Contents for SN-TPT4231
























































































Search results

Summary of Contents for SN-TPT4231

Reviews:

Related manuals for SN-TPT4231

Brands by name

Popular brands

Sunell Security SN-TPT4231, User Manual

Search results

Summary of Contents for SN-TPT4231

Reviews:

Related manuals for SN-TPT4231

Brands by name

Popular brands