manualshive.com logo in svg

Sun Microsystems StorEdge N8400, Installation, Configuration, And Service Manual, Page: 36 / 38

Share
Download
Sun Microsystems StorEdge N8400 Installation, Configuration, And Service Manual Download Page 36

36

Sun StorEdge N8400 Filer Installation, Configuration, and Service Guide • August 2001

Note –

In some cases, if a disk drive is removed and replaced on a powered-off or

incompletely booted array, the internal system monitoring facilities may not
correctly detect the drive replacement. Therefore, always replace disk drives on
powered-on, fully booted arrays only.

For more information refer to:

■

Sun StorEdge T3 Array Installation, Operations, and Service Manual

■

Sun StorEdge T3 Array Administrator’s Guide

▼

To Verify Drive Reconstruction

To check the status of a drive and verify the reconstruction of the data, choose one of
the two following methods:

■

Visual. When you place the new drive into the array, the following sequence
should take place:

■

Disk drive amber LED blinks fast. Disk is spinning up.

■

Disk drive green and amber LEDs blink fast. Disk is being initialized.

■

Disk drive green LED blinks fast and amber LED is steady. Disk is being
reconstructed.

■

Disk drive green LED is steady. Done.

■

Telnet. Start a telnet session to the array and use the

proc list

command via

the array’s command-line interface (CLI).

Note –

Do not confuse the array CLI with the filer CLI. The filer CLI is used to

access a simplified set of commands to manage the system.

An output similar to the following should be displayed.

t300:/:<35> proc list

VOLUME

CMD_REF

PERCENT

TIME

COMMAND

v1

20241

23

0.09

vol recon

Summary of Contents for StorEdge N8400







































Reviews:

No comments