manualshive.com logo in svg

Sun Microsystems StorEdge N8400, Installation, Configuration, And Service Manual, Page: 22 / 38

Share
Download
Sun Microsystems StorEdge N8400 Installation, Configuration, And Service Manual Download Page 22

22

Sun StorEdge N8400 Filer Installation, Configuration, and Service Guide • August 2001

▼

To Configure the Arrays for Monitoring

The arrays can now communicate across the management LAN. You must now add
the Sun Enterprise 420R Server IP address into the

syslog.conf

file of both the

MCU and the alternate MCU of each partner group.

▼

To Transfer the Array

syslog.conf

File to the Server

1. To enable an ftp connection to the array, set the root password using the

passwd

command.

2. Start an ftp session from the server to the array.

For example:

3. Log on to the array by typing

root

and then your password at the prompts.

4. Access the

/etc

array directory using the

cd

command.

T300

name

:/:<

n

> passwd

OLD password:

[old] password

NEW password:

[new] password

NEW password (confirm):

[new] password

# ftp 192.148.226.11

Connected to 192.148.226.11.

220 server-name FTP server (SunOS 5.8) ready.

Name (192.148.226.11:root):

Name (192.148.226.11:root): root

331 Password required for root.

Password:

password

230 User root logged in.

ftp>

ftp> cd /etc

250 CWD command successful.

ftp>

Summary of Contents for StorEdge N8400







































Reviews:

No comments