manualshive.com logo in svg

Sun Microsystems StorEdge N8400, Installation, Configuration, And Service Manual, Page: 25 / 38

Share
Download
Sun Microsystems StorEdge N8400 Installation, Configuration, And Service Manual Download Page 25

Sun StorEdge N8400 Filer Installation, Configuration, and Service Guide

25

6. Copy the

syslog.conf

file from your working directory to the

/etc

directory on

the array using the

put

command.

7. Exit the ftp session using the

bye

command.

8. Access the array by either a telnet session or a serial connection.

9. Reboot the array by typing the following:

10. Repeat “To Configure the Arrays for Monitoring” on page 22 for both arrays of

each remaining partner group.

This completes setting up the arrays for monitoring.

ftp> put syslog.conf

200 PORT command successful.

150 ASCII data connection for syslog.conf (192.148.226.11.34511)

226 ASCII transfer complete.

local: syslog.conf remote: syslog.conf

20 bytes received in 0.0021 seconds (94.81 Kbytes/s)

ftp>

ftp> bye

221 Goodbye.

#

t300:/etc:<

n

> sync

t300:/etc:<

n

> reset

Reset the system, are you sure? [N]: Y

Summary of Contents for StorEdge N8400







































Reviews:

No comments