background image

OnAir 1000 Digital Mixing Console

Date printed: 23.10.03

SW V 4.0

SW Update  12-1

12

 

SW UPDATE

12.1

 

Software Structure

The OnAir 1000 software consists of the following packages:

CPU software

DSP software

Peripheral modules and surface control software.

12.1.1

 

CPU Software Package

Boot Software

The boot software part is installed in an EPROM and consists of:

Hardware initialization

Elementary hardware tests

Start-up (or loading) of the application.

Application Software

The application part of the software package covers the remaining console
functions. Program and data (current status, snapshots, configuration...)
remain stored in memory after power-off, so that neither program nor data
have to be loaded during normal operation. This is achieved by using a
Flash memory.
The application software is loaded at the first start-up of the console (in
the factory), and afterwards due to new releases and upgrades only. Pro-
gram and data are installed in a Flash memory.
The application software is loaded from PC-Cards. For this purpose, read-
only cards can be used.

12.1.2

 

DSP Software Package

The DSP software package is treated the same way as the CPU software
package (application software).

12.1.3

 

Important Information for Software Update to V4.0

Software V4.0 requires compatible Control Front Board I firmware.
If software V4.0 is loaded without the corresponding firmware, the console
will be blocked and cannot be used. In this case, either the former main
software has to be re-loaded, the new Control Front Board I firmware must
be installed, or the Control Front Board has to be replaced.

Studer will not take any responsibility nor accept warranty claims for not
following this procedure.

Please make sure that the console data are backed-up prior to any modifi-
cation as the internal data structure is different. Note the current customer
code setting (refer to 

chapter 11.2.11

).

Summary of Contents for SW V4.0 OnAir 1000










































































































































































































































































































































































Reviews: