Studer SW V4.0 OnAir 1000 Operating And Service Instructions Download

Page: 122 / 361

OnAir 1000 Digital Mixing Console

13-4 Diagnostics

SW V 4.0

Date printed: 23.10.03

Diagnostics and Error Handling – Flash Checksum Tests

Error ID

Type

Indication

Diag. Box

Error Text (Conflict)

054

Warning

yes

Flash verification - All Snapshots, Mic Settings and Channel
Routings lost due to software version mismatch!

055

Warning

yes

Flash verification - Customer Configuration corrupted!

056

Warning

yes

Flash Verification - Console Configuration corrupted!

057

Warning

yes

Flash Verification - Current Console State corrupted!

058

Warning

yes

Flash Verification - Snapshot Block Checksum Verification
Failure! [n] of [m] Global Snapshots loaded.

059

Warning

yes

Flash Verification - Mic Setting Block Checksum Verification
Failure! [n] of [m] Global Mic Settings loaded.

072

Warning

yes

Flash verification - Channel Routing Block Checksum
Verification failure! [n] of [m] channel routings loaded.

Diagnostics and Error Handling – PC-Card Battery Tests

Error ID

Type

Indication

Diag. Box

Error Text (Conflict)

060

Information

yes

PC-Card Slot [%] – Card battery low. Replace battery
immediately!

061

Warning

yes

PC-Card Slot [%] – Card battery dead. Replace battery
immediately!

Diagnostics and Error Handling – Flash Checksum Tests

Error ID

Type

Indication

Diag. Box

Error Text (Conflict)

062

Warning

yes

Flash verification – Snapshot Block Checksum Verification
failure! [n] of [m] Private Snapshots loaded.

063

Warning

yes

Flash verification – Snapshot Block Checksum Verification
failure! [n] of [m] Private Mic Settings loaded.

Configurator

Error ID

Type

Indication

Diag. Box

Error Text (Conflict)

064

Information

yes

Load Configuration Failure due to channel type mismatch!
Channel [n] input parameters not reconfigured.

065

Information

yes

Load Configuration Failure due to missing Channel Data in
Configuration File! Channel [n] - [m] not reconfigured.

066

Information

yes

Load Configuration Failure due to missing Input Data in
Configuration File! Channel [n] Input 3 - 6 not reconfigured.

067

Information

yes

Restore Configuration Failure due to channel type mis-
match! Channel [n] not restored during EXIT.

068

Information

yes

Restore Configuration Failure due to number of channels
mismatch! Channel [n] - [m] not restored during EXIT.

069

Information

yes

Restore Configuration Failure due to number of inputs
mismatch! Channel [n] Input 3 - 6 not restored during EXIT.

073

Information

yes

Input Selection for Channel [n] not activated, since the
number of Inputs is 2 instead 6!

074

Information

yes

New Channel Routing not activated, since the number of
Channels or the number of Fader strips doesn't match the
current configuration!

075

Information

yes

Global Channel Routing not activated, since the number of
Channels or the number of Fader strips doesn't match the
current configuration!

Snapshot Controller

Error ID

Type

Indication

Diag. Box

Error Text (Conflict)

080

Information

yes

Snapshot Recall not completed due to missing Input Data in
Snapshot! Channel [n] Input 3 - 6 not recalled.

081

Information

yes

Snapshot Recall not possible due to corrupted Snapshot
Data!

096

Information

yes

All Global Channel Routings used. - Only [n] of [m] Global
Channel Routings loaded!

097

Information

yes

All Global Snapshots used.- Only [n] of [m] Global
Snapshots loaded!

098

Information

yes

All Private Snapshots used.- Only [n] of [m] Private
Snapshots loaded!

099

Information

yes

Snapshot Recall Failure due to channel type mismatch!
Channel [n] not recalled.

100

Information

yes

Snapshot Recall not completed due to missing Channel
Data in Snapshot! Channel [n] - [m] not recalled.

101

Information

yes

All Global Mic Settings used.- Only [n] of [m] Global Mic
Settings loaded!

102

Information

yes

Mic Setting not created - Input must be of type microphone!

103

Information

yes

Mic Setting not recalled - Input must be of type microphone!

Summary of Contents for SW V4.0 OnAir 1000










































































































































































































































































































































































Search results

Summary of Contents for SW V4.0 OnAir 1000

Reviews:

Related manuals for SW V4.0 OnAir 1000

Brands by name

Popular brands

Studer SW V4.0 OnAir 1000, Operating And Service Instructions

Search results

Summary of Contents for SW V4.0 OnAir 1000

Reviews:

Related manuals for SW V4.0 OnAir 1000

Brands by name

Popular brands