manualshive.com logo in svg

Studer SW V4.0 OnAir 1000, Operating And Service Instructions

Share
Download
Studer SW V4.0 OnAir 1000 Operating And Service Instructions Download Page 154

OnAir 1000 Digital Mixing Console

15-4  DIP Switches and Jumpers

SW V 4.0

Date printed: 23.10.03

15.4

 

Analog Output Units

The Analog Output units have jumpers for mono/stereo selection and for
selecting the desired output signal, individually for each of the outputs A
and B.
The output level is set with trimmer potentiometers, separate by outputs
A/B and by left/right channels.

15

16

17

15

16

17

RA1

OUTPUT LEVEL

A RIGHT

RA2

OUTPUT LEVEL

A LEFT

RA3

OUTPUT LEVEL

B RIGHT

P56 P57 P58

P59

RA4

OUTPUT LEVEL

B LEFT

P55

B MONO

B STEREO

P26

P13

P53

P40

P15

P2

P42

P29

A
B

P27

P28

P41

P54

P14

A STEREO

A MONO

not 

assigned

 - 

PFL

not 

assigned

 - 

TALKBACK

not 

assigned

 - 

N–1 A

not 

assigned

 - 

OUT1

not 

assigned

 - 

AUX1

not 

assigned

 - 

AUDITION

not 

assigned

 - 

PGM

not 

assigned

 - OUT2

Pos. 17, lower - N–1 B

Pos. 16, lower - 

AUX2

Pos. 15, lower - 

RECORD

PFL

 - not 

assigned

TALKBACK

 - not 

assigned

N–1 B

 - not 

assigned

OUT1

 - not 

assigned

AUX2

 - not 

assigned

AUDITION

 - not 

assigned

RECORD

 - not 

assigned

OUT2 - not assigned

N–1 A - Pos. 17, upper

AUX1 - Pos. 16, upper

PGM - Pos. 15, upper

not 

assigned

not 

assigned

Summary of Contents for SW V4.0 OnAir 1000










































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands