Stryker 220-200-000 Service Manual Download Page 64

Page: 64 / 71

17.0 Bulb Fan

Seq.

Task

Description

Figure

Tools

Needed

Parts

1690

Remove Chassis Cover
from Chassis (procedure
1.0). Remove the Bulb
Assembly.

1700

Disconnect 3-Wire Fan
cable from Control Board
connector J9 (BULB FAN).

• 3-Wire Fan

Cable from
Bulb Fan (3-
Pin 3-Wire)

• X8000 Control

Board (873)

1710

Use a screwdriver to pop
rivets on the bulb duct free
and remove duct.

• Flathead

Screwdriver.

• Nylon Snap

Rivets (4)
(816)

• Bulb Duct

(325)

• 3-Wire Fan

(507)

1720

Remove nuts from PEMs
and remove fan.

• 11/32”

Wrench

• #8-32 KEP

Nuts (3) (491)

• 3-Wire Fan

(507)

• Fan Duct

(498)

• X8000 Chassis

(343)

1730

Remove wire tie securing
3-Wire Fan cable from Bulb
Fan to Separator as shown.
Remove Fan and get new
Fan.

• Cable Tie

Cutters

• Standard

Cable Tie
(873)

• Separator

(328)

• Bulb Fan

Cable (507)

Summary of Contents for 220-200-000








































































Search results

Summary of Contents for 220-200-000

Reviews:

Related manuals for 220-200-000

Brands by name

Popular brands

Stryker 220-200-000, Service Manual

Search results

Summary of Contents for 220-200-000

Reviews:

Related manuals for 220-200-000

Brands by name

Popular brands