Stryker 2031 Maintenance Manual Download Page 37

Page: 37 / 185

page 4–10

Head Wall Output Configuration

37–PIN CONNECTOR

Pin 1

Option 2 Common

Pin 2

Read Light

Pin 3

Room Light

Pin 4

Speaker High

Pin 5

Pot Wiper

Pin 6

Radio Common

Pin 7

Nurse Call Interlock

Pin 8

Audio Transfer –

Pin 9

Audio Tr

Pin 10

Int

Pin 11

Interlock –

Pin 12

Spare

Pin 13

Options 3 Common

Pin 14

Pot Low Common

Pin 15

Pot High Common

Pin 16

Nurse Answer Light +

Pin 17

Option 1 NO/NC

Pin 18

Option 1 Common

Pin 19

Nurse Call Light +

Pin 20

Option 2 NO/NC

Pin 21

Option 3 NO/NC

Pin 22

Option 3A NO/NC

Pin 23

Option 2A Common

Pin 24

Option 2A NO/NC

Pin 25

Nurse Call +

Pin 26

Nurse Call NO/NC

Pin 27

Room/Read Light Common

Pin 28

Nurse Call Light –

Pin 29

Nurse Answer Light –

Pin 30

Priority NO/NC

Pin 31

Priority Common

Pin 32

Option 3A Common

Pin 33

TV –

Pin 34

TV +

Pin 35

Speaker Low Common

Pin 36

Audio Shield

Pin 37

Radio NO/NC

STRYKER PENDANT PORT

Scan Line

Audio (–)

Nurse Call (+)

+5 VDC

Scan Line

Nurse Call (–)

TV Channel Up

Backlight

Audio (+)

Gatch Up/Fowler In/Foot Up/DMS Firm

Gatch Down/Fowler Out/Foot Out/DMS
Soft

Fowler Up/Trend In

Fowler Down/Trend Out

Audio Shield

Not Used – Socket Filled

Bed Up

Ground

Read Light/Bed Down

Room Light

Summary of Contents for 2031


























































































































































































Search results

Summary of Contents for 2031

Reviews:

Stryker 2031, Maintenance Manual, Page: 37 / 185

Search results

Summary of Contents for 2031

Reviews: