Stryker 2031 Maintenance Manual Download Page 138

Page: 138 / 185

Head End Siderail Assembly, Left and Right

page 10–61

2030–20–11 Standard Siderail

Item Part No.

Part Name

Qty.

2035–000–100 Label, Standard, Left

2035–000–200 Label, Standard, Right

3001–400–953 Switch Cap

3001–400–522 Filler Cap

3001–400–517 Speaker Seal

3001–400–535 Inner Panel Blank Module

2030–000–300 Label, Standard, Left

2030–000–400 Label, Standard, Right

2030–20–12 Standard Siderail with Nurse Call

Item Part No.

Part Name

Qty.

2035–000–101 Label, Standard, NC, Left

2035–000–201 Label, Standard, NC, Right

3001–400–953 Switch Cap

3001–400–522 Filler Cap

3001–403–831 Speaker with Cable

3001–400–535 Inner Panel Blank Module

2030–000–301 Label, Standard, NC, Left

2030–000–401 Label, Standard, NC, Right

2030–20–15 Standard Siderail w/NC & Comm.

Item Part No.

Part Name

Qty.

2035–000–102 Label, Standard, Left

2035–000–202 Label, Standard, Right

3001–400–953 Switch Cap

3001–400–522 Filler Cap

3001–403–831 Speaker with Cable

3001–400–535 Inner Panel Blank Module

2030–000–301 Label, Standard, NC, Lt.

2030–000–401 Label, Standard, NC, Rt.

Right Inner Siderail Label

Right Outer Siderail Label

Right Inner Siderail Label

Right Outer Siderail Label

Right Inner Siderail Label

Right Outer Siderail Label

Summary of Contents for 2031


























































































































































































Search results

Summary of Contents for 2031

Reviews:

Stryker 2031, Maintenance Manual, Page: 138 / 185

Search results

Summary of Contents for 2031

Reviews: