Unitom-50
Instruction Manual
Unitom-50
Safety Precaution Sheet
To be read carefully
before use
1.
The operator(s) should be fully instructed in the use of the machine and its cut-
off wheels according to the Instruction Manual and the instructions for the cut-
off wheels.
2.
The machine must be placed on a safe and stable support table. All safety
functions and guards of the machine must be in working order.
3.
The unit must be installed in compliance with local safety regulations
4.
Use only intact cut-off wheels. The cut-off wheels must be approved for min. 50
m/s.
5.
Observe the current safety regulations for handling, mixing, filling, emptying and
disposal of the additive for cooling fluid.
6.
The workpiece must be securely fixed in the quick-clamping device or the like.
Large or sharp workpieces must be handled in a safe way.
7.
Do not touch anything inside the cutting chamber while positioning the cut-off
wheel with the position button.
8.
Struers recommends the use of an exhaust system as the materials to be cut
may emit harmful gasses or dust.
9.
The machine emits only moderate noise. However, the cutting process itself
may emit noise, depending on the nature of the workpiece. In such cases, use
of hearing protection is recommended.
10.
The machine must be disconnected from the mains prior to any service.
11.
Use of working gloves is recommended as workpieces may be both very hot
and produce sharp edges.
If optional rubber curtains are needed in order to cut long, protruding workpieces:
1.
Check with your local authorities whether rubber curtains are approved as
protection in your country.
2.
Do not put hands through the rubber curtain during operation of the machine.
3.
Protruding workpieces should be shielded or marked.
The equipment is designed for use with consumables supplied by Struers. If subjected to misuse, improper
installation, alteration, neglect, accident or improper repair, Struers will accept no responsibility for
damage(s) to the user or the equipment.
Dismantling of any part of the equipment, during service or repair, should always be performed by a qualified
technician (electromechanical, electronic, mechanical, pneumatic, etc.).
Summary of Contents for Unitom-50
