STM SatLink User Manual Download Page 16

Page: 16 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 16

4.1.1 Dynamic IP configuration of PCs connected to the STM SatLink Terminal LAN

By default the DHCP server in the STM SatLink Terminal is enabled. When the STM SatLink Terminal

is powered on, all PCs connected to the STM SatLink LAN can automatically retrieve their IP

configuration from the DHCP server. The user should verify that the Window clients are configured to

obtain an IP address and DNS server address automatically. Figure 11 shows the correct Windows XP

configuration when the DHCP server is enabled in the Terminal.

Figure 11: Windows XP TCP/IP setting when DHCP server is enabled in the Terminal

From an MS-DOS window, the user may type

ipconfig /all

command to verify that the computer has

received correct configuration parameters from the DHCP server such as IP address, subnet mask, default

Gateway, DNS servers and lease time.

Figure 12:

ipconfig /all

print out from an MS-DOS window

Summary of Contents for SatLink











































































































Search results

Summary of Contents for SatLink

Reviews:

Related manuals for SatLink

Brands by name

Popular brands

STM SatLink, User Manual

Search results

Summary of Contents for SatLink

Reviews:

Related manuals for SatLink

Brands by name

Popular brands