STM SatLink User Manual Download

Page: 82 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 82

Appendix G. ODU installation

The ODU comprises the antenna with feed-horn and mounting structure, and a transceiver that contains

the LNB integrated with OMT, Tx-reject filter, and the transmitter (BUC). If the STM SatLink 4033/4035

transceiver is not used, the OMT, LNB and BUC may be supplied as two or three separate units. Two

cables with F-connectors, one for Tx and one for Rx are connecting the ODU to the IDU.

Figure 19: STM SatLink 4033/4035 Configuration

G.1 Assembly of SatLink 403x transceiver to feedhorn

The STM SatLink 403x is supplied with 6 pcs of UNC 6/32 for connection to the antenna flange. The

parts are shown in the picture below. Please refer to Appendix I for information of how to connect the

STM SatLink 403x to antenna feed horn interfaces with 6 or 8 M4 screws.

Figure 20: SatLink 4033/4035 and screws for mounting feed horn

Transceiver

mounted

directly on

antenna

feed

Antenna

Feed Horn

Antenna

Reflector

Summary of Contents for SatLink











































































































Search results

Summary of Contents for SatLink

Reviews:

Related manuals for SatLink

Brands by name

Popular brands

STM SatLink, User Manual

Search results

Summary of Contents for SatLink

Reviews:

Related manuals for SatLink

Brands by name

Popular brands