STM SatLink User Manual Download Page 7

Page: 7 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 7

1.2

Initial Configuration

The STM SatLink Terminal must be configured before it can communicate via the satellite to and from

the network operator Gateway. The parameters to be configured are explained in section 6.2.

The configuration of the terminal can be carried out using the configuration tools:

•

Command Line Interface

Via RS232/Terminal emulator (e.g. HyperTerminal)

Telnet

•

Web-interface

•

SNMP

Configuration via CLI and Web-interface is presented in this document. For terminal management via

SNMP, the reader is referred to [6].

1.3

Symbols

NOTE

Additional information that the reader should pay special attention to.

WARNING

System malfunction may occur if the warning-information is violated.

Summary of Contents for SatLink











































































































Search results

Summary of Contents for SatLink

Reviews:

Related manuals for SatLink

Brands by name

Popular brands

STM SatLink, User Manual

Search results

Summary of Contents for SatLink

Reviews:

Related manuals for SatLink

Brands by name

Popular brands