Stihl FS 40 Service Manual Download Page 67

Page: 67 / 82

Series 4144 Components FC, FS, KM

Machines with bike handle

Tighten down the screws
(arrows) firmly.

– Install the control handle,

7.4

– Check instruction label on drive

tube for damage and legibility,
replace if necessary.

– Tightening torques,

3.4

9.1.1

Disassembling (KM 56)

– Remove the drive tube,

9.1

– Remove the loop handle if

necessary,

9.1.7

– Remove the carrying ring if

necessary.

– Loosen the wing screw (1) and

pull out the attachment.

Loosen the screw (arrow).

– Pull the coupling sleeve (2) off

the drive tube (3).

545RA007 TG

545RA232 TG

Pull the drive shaft (1) out of the
drive tube.

If the drive shaft has turned blue,
install a new one.

Pry the plug (1) out of the drive
tube.

Pull the flexible liner out of the
drive tube.

545RA234 TG

545RA233 TG

545RA235 TG

Grip the collar (arrow) and pull
the complete driver (1) out of the
drive tube.

Do not apply tool to plastic lug (2)
since it might break.

Remove the E-clip (1).

– Remove the washer (2) and

bushing ((3) and the second
washer.

Pull out the wire clips (1).

– Check the individual parts and

replace if necessary.

545RA236 TG

545RA237 TG

545RA238 TG

Summary of Contents for FS 40



















































































Search results

Summary of Contents for FS 40

Reviews:

Related manuals for FS 40

Brands by name

Popular brands

Stihl FS 40, Service Manual

Search results

Summary of Contents for FS 40

Reviews:

Related manuals for FS 40

Brands by name

Popular brands