Stihl FS 40 Service Manual Download Page 52

Page: 52 / 82

Series 4144 Components FC, FS, KM

8.4.4

Throttle Lever /
Rotary Knob

– Remove the carburetor,

8.2

Take out the screw (arrow).

– Pull off the throttle lever (1).

Remove the E-clip (1).

Remove the pin (2) and
washer (3).

– Check the individual parts and

replace if necessary.

– Reassemble in the reverse

sequence.

545RA198 TG

545RA199 TG

Position the throttle lever (1) so
that the pin (arrow) faces up.

– Push the throttle lever (1) on to

the end of the throttle shaft
(arrow).

Tighten down the screw (2)
firmly.

– Check operation.

Rotate the choke shaft. The
choke lever (1) must engage the
throttle lever (arrow).

545RA200 TG

545RA201 TG

545RA202 TG

Take out the screw (arrow).

– Pull off the rotary knob (1).

Remove the spring (1).

– Check the individual parts and

replace if necessary.

Turn the rotary knob (1) until it is
locked in the guide sleeve (2).

545RA087 TG

545RA095 TG

545RA096 TG

Summary of Contents for FS 40



















































































Search results

Summary of Contents for FS 40

Reviews:

Related manuals for FS 40

Brands by name

Popular brands

Stihl FS 40, Service Manual

Search results

Summary of Contents for FS 40

Reviews:

Related manuals for FS 40

Brands by name

Popular brands